Відео

After tighting the 2 parts in the heater block I solved the problem by covering the nozzle hole with a finger and sucking the air with my mouth and pass it to my tongue for some time. If it keeps there for another while I am pretty sure there will be no leaking, always worked for me and I never had that problem again.

Is that a ford focus se?

Copper washers on aluminum housings can create galvanic corrosion.

Has this box held up over time for you?

Tutorial pliss

I hate 3D printing so much it's unreal

Leaks always cause stoppages for me where the printer spontaneously stops and I have to abort the print. My last attempt did and don't look bad. No stringing but the print failed to complete and that takes almost an entire day to print

Was this just a squire telacaster or the affinity series one?

You rock!

Great video

Hydraulic oil on rubber... what could go wrong? Love the Focus but these are more planned obsolescence crap just like the lifetime air filters.. Polyurethane mounts is a much better option.

hi all, is there a way to find LD6000 firmware anywhere?

Thank you for the information. Heading out to Home Depot today to build one for myself!

Name of the song?

Thanks, 15 minutes for a 5-minute explanation, & I'm being generous. Much scrolling ahead needed. It seems such an "American" thing to be extremely long winded. Who would have thought. However, thanks anyway, I imagine you mean well.

I bought all three mounts as a set on Amazon for $70 in early 2024. swapped them out with a floor. Jack and a few handtools, took an hour and 15 minutes working casually. The car feels like it’s brand new.

On amazon it says that it dosent fit my 2007 focus, but when I looked at all the trims they said that none of them would work with this oem? Am I just dumb?😂

Great... That's exactly how it works best. Due to problems with the heating capsule, I bought a new hotend because it has 2 fixing screws, better than the one that came with it. At the moment I'm trying to improve the hotbed base with the ruler bearings. The printer is an Anet E10 in the process of being converted the controller box disappears, the holder has already been printed out. The conversion is now starting. I hope everything fits and works as I imagine.

Nice work! I’m trying build one of these, for chilling beer, mine is a bit different, electric panel on off switches, gonna try to just hookup a plug in temp controller instead of all the wiring you did. I’m impressed!

Anyone have archives of these files? I just got a ft-5 but with FT shutting down I cannot for the life of me find the firmware to install.

DEA/Marmon makes a hydraulic aftermarket heavy duty mount. Lifetime warranty.

I have an 06 zx4 5 speed manual, whenever I go to take of the front passenger side has alot of vibration and sometimes feels smooth mainly vibrates when gas is applied leading me to this video

Thank you! I've been fighting this exact problem and it's surprisingly hard to find advice on fixing it. The walkthrough of connecting the heatbreak and nozzle was exactly what I needed. Thanks for making this vid

When i assemble the hotend like this, and i want to change the nozzel, if i lose the nozzle, the heartbreak will become loose, so i need to take the hotend out and do it all again, just to change the nozzle

Hi bro, I'm doing a school proyect, I'm really interested in this topic but and I can't quite understand how it cools the machine, I will apreciate if you could help me. really nice video

Thank you for this video! This was very helpful!

My 2007 has the same vibration, I will try the motor mount THANK YOU.

How about a corrosion update? Have you had any issues 8 months later? I really enjoyed this 3 part series as im looking to build one of these myself!

Thanks

I had to replace a hot end and i keep geeting different reults get one step closer and feel like everytime i go back to research i discover soemthing new lol. I bet this is the final piece im lacking because the heatblock assembly from creality the nozzle was butt up against the block.

3:33 timestamp mark

At 9:05 it looks like those pinch weld blocks were bending the lower part of the plastic trim that comes right up to the pinch welds. Did that do any damage?

Its like u made these videos for me haha, cause i am an electrician.😅

Laser....😅 this is gonna cool my condenser and save me so much money on my water bill lol. Again thanks bro im bulding mine tomorrow and do a spirit run i just did 2 stripping runs and i want to do my spirit run with super cold water. This is gonna be the best rum i have ever made.

Thanks!

Man I am stepping up my production but I'm also on a budget. I search thru water chillers for hours and I didnt want to risk it and waste $150 on some sketchy brand. I have 2 of those similar 5000btu and a 10000btu and I was like why couldn't I make one. I tried a few other ones that came up first but it didn't make it into the video like a minute and thru some scrolling found ur part 2 of this so i came over to part 1. This was done PERFECTLY bro, its exactly what I was looking for. Thank u.

Where did you get the cordless Ratchet? What brand is it. Thanks

Awesome!!

Add rubber

My dvd with drivers is offline , 7 years ago who giving away the drivers?

Having problems w new ender 3 pro. Had a major hot end blowout. All pre-assembled "plug and play", do not fuck w from factory. Once I get thru all the pla I feel like I'm gunna see a gap right where he describes. They don't even need to do a Q.C. just put a step in the assembly directions that says check this dimension before assembly.

Thanks very helpful information. I knew the OEM passenger side engine mount was fluid filled, but I didn't know the aftermarket one was not. Good looking out DC!

Do you need jack point pucks (pads) for each of the lift points on the Bolt?

I know this is pretty late, but you should try to NOT use antifreeze in a laser. It will exponentially increase the likelihood that the laser arcs inside itself.

go with OEM for the torque one as well. Used after market on all three, two failed and I got OEM main one and torque and all is good again.

this happens because faulty adapter( box with power wire)

Have you had any issues with this system?

Fuck me, why do I have to do this on my brand new printer. I've come across issues at every single step holy shit.

Why not use thread locker ?

The jack point is a white flat square near the front wheel. It will raise the entire side.